Diseño de circuitos Jobs

Experienced KiCad Hardware Engineer – Schematic Capture, DFM-Optimized PCB Layout & Production Package (Turnkey JLCPCB Assembly) Job Description: Honeycomb LLP is seeking an experienced embedded hardware and PCB design engineer to take a product design from initial block diagram/specifications through complete schematic capture, PCB layout, and turnkey assembly package delivery. The board will host an embedded microcontroller ecosystem (e.g., ESP32 / RP2040 / STM32) interfacing with sensors and power management circuits. The final design must be fully optimized for cost-effective manufacturing and assembly via JLCPCB SMT services. Scope of Work & Responsibilities: 1) Schematic Capture: Design modular, production-ready schematics in KiCad (latest stable version) adhering...

TI-84 PLUS + ESP32-S3 + OV5640 AI CALCULATOR BUILDER SPECIFICATION 1. PROJECT OVERVIEW Build a modified TI-84 Plus non-CE calculator with an internally installed Seeed Studio XIAO ESP32-S3 Sense, OV5640 5MP autofocus camera, Wi-Fi, OpenAI API connectivity, TI-84 to ESP32 communication, and a calculator-side AI interface. System architecture: OV5640 camera -> ESP32-S3 -> Wi-Fi -> OpenAI API -> ESP32-S3 -> TI-84 -> Display The ESP32-S3 handles camera control, image processing, networking, and AI communication. The TI-84 provides the keyboard, display, user interface, and commands. Use the existing TI84-AI GitHub project by ivan-grebe as the primary software and architecture reference: Do not simply adapt an ESP32-C3 tutorial. This build specifically uses an ESP32-...

1) Need to do total re routing 2) need to add esp32 c6 wroom 1 vis uart,spi and i2c 3) add eeprom 4) correct modbus error 5) re naming all I/O

I’m upgrading our facility’s power resilience and need a licensed electrician who has hands-on experience installing rack-mounted UPS units in a commercial environment. The job involves receiving the new rack UPS on site, mounting it securely in the existing server rack, tying it into the dedicated 208 V circuit already pulled to the data room, verifying grounding, and performing a full load test with our IT team before hand-over. You should be comfortable working around running equipment, Please bring the tools required for safe lift-in. Deliverables expected: • Fully installed rack UPS, cabled and labeled • Commissioning report showing voltage, amperage, battery diagnostics, and 30-minute load test results • The existing Commando plug will be removed...

Need small anf compact HDI multilayer pcb from systematic to pcba which can be connected with my existing smartphone pcb . Requirement in custom pcb are - 1) NFC + custom NFC antena 2) Secure element 3) secure MCU 4) type C USB for data 5) vibrator 6) touch buttons 7) pogo pins for charging BOM and all details of my main pcb will be discussed and provided to you

I already have a complete schematic and BOM for an embedded-system board and now need someone to turn it into a production-ready PCB in KiCad. You will receive the schematic, component list, and the exact board outline with mounting-hole locations so the size constraint is fixed from the start. Your task is to place all parts logically for signal integrity and serviceability, route power and ground planes cleanly, add connectors exactly where the enclosure dictates, and run full DRC to be certain the board will pass fabrication checks the first time. Please keep an eye on trace widths, clearances, and manufacturability rules that mainstream fabs expect. When finished, send me: • The complete KiCad project (schematic symbols, footprints, and PCB layout) • Gerber and drill fil...

Our company needs the Electrical - Mechanical Engineer!!! >>>To show that you have carefully reviewed this job posting, please check my location (country) and state—at the very beginning of your proposal—the time calculated by subtracting one hour from my local time.>>> (Job Title) Electrical - mechanical Engineer for Medium-Voltage Line Sensor Prototype (Job Description) Important availability and engagement requirements: This is a fixed-price project only - no hourly billing and no upfront payment. Payment will be tied to agreed project milestones/deliverables. We need someone who can commit approximately 60 hours per week, work primarily in the US Pacific Time (PST/PDT) zone, and be available for real-time communication throughout the working day. We a...

I will give you a complete distortion/overdrive guitar-pedal schematic along with a list of the exact parts I want to use. Your job is to recreate that digital circuit in EasyEDA, make sure every symbol and footprint matches the components I provide, and lay out a compact, noise-conscious PCB that can go straight to fabrication. Because this is a digital circuit for an audio pedal, trace placement, ground routing, and jack positioning matter; please keep signal integrity and pedalboard ergonomics in mind while arranging the board. I’m happy with through-hole as long as the parts remain the same ones on my list. Deliverables • EasyEDA project file with the full schematic entered • Optimised PCB layout inside the same project • Generated Gerber/NC drill set ready f...

I need a complete high-frequency RF PCB laid out in KiCad for a signal-processing application. The board must integrate antennas directly on the substrate; no filters or discrete amplifiers are planned at this stage, so every trace, via, and ground return has to be optimized for clean, low-loss feed to the antenna structure. Scope • Translate my existing schematic (KiCad format) into a production-ready multilayer layout. • Model and route all RF paths with controlled impedance, proper stack-up definition, and tight clearance to meet high-frequency performance targets. • Design and tune the on-board antenna geometry, matching network, and keep-out regions inside KiCad’s PCB editor and 3D viewer. • Run DRC, ERC, and any KiCad integrated RF simulation tools ...

We are seeking an experienced PCB designer to create a compact, single-board PCB that integrates the following components: - High-precision GNSS receiver IC (u-blox ZED-F9P) - ESP32-S3 Wi-Fi/Bluetooth microcontroller module - 9-axis IMU (Bosch BNO055) - Buck-boost power management circuit for single-cell Li-Ion battery operation - Input protection circuitry (over-voltage, over-current, reverse polarity) - Dual antenna connectivity (SMA and connectors) The board must be production-ready, reliable in field conditions, and designed per industry standards. Deliverables include schematic, PCB layout files, BOM, and Gerber outputs. The designer can use KiCad or EasyEDA as the design tool. Full schematics, pin allocations, firmware interface details, and application context will be shared post...

Job Description We are looking for an experienced hardware/embedded engineer for an upcoming wearable product development project. The product is a compact wrist-worn connected device, and we need someone who has previously taken a wearable or similar battery-powered consumer electronics product from hardware design through prototyping and manufacturing. The device will involve: - Custom PCB / electronics design - Bluetooth Low Energy (BLE) - Microphone + speaker / two-way audio - Low-power embedded firmware - Battery and power optimisation - Wireless charging - Compact wearable enclosure / CAD - Prototype development and testing - DFM and manufacturing handoff The final project will require complete production-ready deliverables including schematics, PCB/Gerber files, BOM, firmware source...

Seeking layout engineer with experience in Altium, low noise analog circuitry, and EMI mitigation. This project encompasses minor updates to an existing board which has already passed EMI testing. There may or may not be a desire to further reduce emissions, but the main focus is signal processing updates.

I need an expert to test and fix circuit components for a radio project. Key tasks include: - Tasting and fixing circuits on both breadboard and PCB - Primarily focusing on transistors and diodes - Diagnosing and resolving short circuits Ideal Skills and Experience: - Proficiency in working with transistors and diodes - Experience with both breadboard and PCB setups - Strong troubleshooting skills for short circuits Looking forward to your bids!

Ik zoek iemand die voor een commerciële elektrische installatie een volledig ééndraadschema opstelt volgens NEN 1010. Wat ik aanlever • Een voorbeeldschema ter referentie • Ruwe lijst met alle groepen en verbruikers Wat jij oplevert • Een duidelijk, professioneel schema in AutoCAD (of vergelijkbaar CAD-pakket) • Alle circuitgroepen overzichtelijk benoemd • Aarding en aardlekschakelaars exact gepositioneerd • Specificaties van apparaten en belastingen per groep vermeld Belangrijk – Het schema moet strikt voldoen aan de NEN 1010-richtlijnen. – Bestandsformaten: dwg én een leesbare PDF. – Heldere layer-structuur en benamingen zodat collega-installateurs het makkelijk kunnen aanpassen. Heb j...

I keep losing power in the living room and bedrooms whenever the same breaker flips, and the issue has become more frequent over the past week. I need someone who can come onsite, trace the wiring on that residential circuit, pinpoint whatever is causing the repeated trips, and confirm the safest long-term fix. Your job is to isolate the fault, explain what’s happening in plain language, and either correct it on the spot or give me a clear written plan—parts, labour and estimated time—so I can approve repairs immediately. A professional toolkit (multimeter, continuity tester, insulation resistance meter) and solid familiarity with domestic wiring regulations are essential. Deliverables: • On-site diagnostic of the affected circuit • Brief report outlin...

We are looking for an experienced RF PCB Layout Engineer to review and complete an existing multi-radio PCB design. This is not a design-from-scratch project. The schematic, component placement and most signal/power routing are already completed. The remaining work is focused mainly on RF layout finalization and production-readiness review. Required experience: Sub-GHz / LoRa RF PCB routing LTE RF layout GNSS RF layout 50-ohm controlled-impedance routing RF matching networks antenna feed layout ground return and stitching-via strategy RF keep-outs and isolation multilayer PCB stack-up EMI/EMC-aware layout KiCad The selected engineer will be required to review the existing PCB, complete/correct the RF sections and bring the board to fabrication-ready status. Expected deliverables incl...

We are looking for an experienced Automotive Electronics / PCB Design Engineer to modify and extend an existing vehicle tracking hardware design into an OBD-II telematics device. The project will include two variants: Modern vehicles – OBD-II with CAN communication. Older vehicles – OBD-II with CAN + K-Line support. We prefer a common hardware platform where possible, with different BOM/configuration options for the two variants. The engineer must have proven experience with OBD-II, CAN Bus, K-Line, automotive power supply/protection, PCB schematic design, and vehicle telematics hardware. Initial deliverables will include the updated schematic, BOM, component selection/alternatives, interface design, automotive protection circuitry, and design documentation. IMPORTANT: Th...

I need a small 33 x 29 mm membrane touch latching switch printed circuit board (PCB) with only 8 SMDs on it, copied for a obsolete device. I'm looking to get 100 of these made, possibly 200 depending on pricing. I can send the 6 component list and photos of the circuit board and a complete circuit board is this 2 sided. The active devices are a ATMEL TINY 13A (needs programming and a PA1CD (i think it's a zener diode, 4 resistors and 1 capacitor. On the decal side there is a small led that lights when latched. It needs to be copied exactly because this switch circuit gets glued into a recess in a plastic case with cutouts for the components so the board lays flat. I may not need the switch decal. Run on a 3.7VDC battery. Key Requirements: - Exact replication of the existing PCB...

I’m leading a senior-year project where my student team will build and test an induction-motor drive (motor, VFD, sensors, protection, filters, the works). What we’re missing is seasoned electrical-engineering insight during the DESIGN phase. Here’s what I’d like from you: • Review and refine our single-line and wiring diagrams, ensuring safe operation on a 3-phase, 480 V supply. • Help size and specify the motor, VFD, fuses/MCB, contactors, braking resistor, EMI/RFI filters, current/voltage sensors, and any surge- or overload-protection devices. • Validate thermal calculations, harmonic considerations and grounding/shielding practices. • Provide a concise Bill of Materials with part numbers and vendor suggestions, flagging long-lead or co...

I have a consumer-electronics concept ready for the next step and need a clean, production-ready double-layer PCB layout. The board will host a mix of through-hole and surface-mount parts, so component placement and routing must accommodate both styles without ballooning the footprint. Deliverables: • Finished design files in Altium and industry-standard Gerbers • Drill files, pick-and-place data, and a tidy BOM (Excel or CSV) • Test PCB's with assembly I will review the Gerbers in ViewMate and run a quick fit-check in our enclosure CAD; the project is complete once the files import cleanly and the report answers all open questions. Looking for someone in India, Delhi NCR Region. Thanks

I need a compact firmware-and-hardware solution that lets a PIC microcontroller, programmed with the XC8 compiler, manage a battery-powered power supply built around a lead-acid pack. Here is what I am after: the PIC should start up from the battery, regulate or switch the output rails as required, continuously read the pack voltage, temperature or any other basic health indicators, and trigger clear actions (for example, low-voltage cutoff or status signalling) before the battery reaches critical limits. A simple serial, I²C or even LED indicator scheme is fine for status feedback—as long as I can read the key parameters easily during bench tests. Please base the code on MPLAB X + XC8 so I can compile and tweak it locally. If you prefer a specific mid-range PIC that is re...

I already have a universal BLDC ceiling-fan driver PCB running perfectly from mains power; what it lacks is an Arduino brain. My goal is to plug an Arduino (Uno, Nano, or whichever you prefer) into the existing driver so I can: • adjust fan speed across its full range, • reverse the direction on command, and • set on/off timers, all through a small set of physical push-buttons mounted near the fan. What I need from you is a clean, well-commented sketch plus a minimal wiring diagram that shows exactly where every button, resistor, and logic-level signal ties into the driver board. If any level-shifting, opto-isolation, or triac/FET gating is required, please spell that out and include the component values. Debounced button handling and non-blocking timer logic (e.g., u...

I’m building a proof-of-concept noise-reduction module destined for consumer-grade electronics. My priority is an electronic schematic that delivers two core capabilities: active noise cancellation and echo reduction. The circuit must be small enough to embed in another typical product that will be mentioned later on as the project develops. Here’s the flow I have in mind. First, we collaborate on the signal-processing topology—feed-forward, feedback, or hybrid—then translate it into a detailed schematic and PCB layout (Altium, KiCad, or your preferred EDA). Once the draft design is ready, I’ll need simulations or bench measurements that prove at least 20 dB attenuation in the 50 Hz–2 kHz band while holding latency under 10 ms; please include SPICE plot...

My final-year electrical engineering project is well underway, but I want the written report to reflect the same level of professionalism as the technical work behind it. I will handle all calculations, simulations, and data; what I need is an experienced engineer—or a writer who routinely prepares professional engineering documents—to help me shape that material into a clear, cohesive LaTeX manuscript. I have 2 separate reports to write. The topic of the first is programming and security-related. The second report is analogue circuit-based. As I said i will do all the technical work; I just need help putting these documents together. The submission for these reports is at the beginning of November and should be roughly 30 pages long. Scope of collaboration • Co-writi...

Industrial 220V Power Supply & Machine ON/OFF Control PCB Design I am looking for an experienced Power Electronics / PCB Design Engineer to design a compact industrial power supply and control circuit that will work with our existing IoT device. Main Requirements - Input: 220–240V AC industrial supply - Provide stable DC power to our existing IoT device - IoT device will provide the control signal for Machine ON/OFF - Circuit must safely switch/control the industrial machine using an appropriate relay/contactor/SSR or other suitable solution - The machine load current will pass through or be controlled by the designed switching section - Proper isolation between high-voltage AC and low-voltage IoT electronics - Include necessary protection: fuse, surge protection, over-current...

I need a detailed design for a 600 amp electrical service for a residential building. The primary use will be general household needs, with high-power cooktops as the only significant appliance. Key Requirements: - Design should accommodate 600 amps for a residential building - Primary use is general household consumption - High-power cooktops to be included in the design Ideal Skills and Experience: - Electrical engineering background - Experience in residential service design - Knowledge of high-amperage systems and safety protocols - Ability to provide detailed schematics and load calculations Please include any relevant certifications and past project examples in your bids. must be certified in new mexico

Taşınabilir bir kontrolcü tasarlıyorum; ESP32, ekran ve joystick gibi tüm bileşenler elimde fakat ekranın ESP32’ye doğru şekilde bağlanması ve çalıştırılması için desteğe ihtiyacım var. Öncelikli hedefim: • Ekranın ESP32’ye hatasız fiziksel bağlantısı (pin planı, güç hatları, arka ışık kontrolü). • Uygun sürücü kütüphanesini (örn. TFT_eSPI, LCD, OLED vb.) yapılandırıp örnek kodla görüntü alabilmek. • Joystick okuma kodunu ekranda canlı gösterecek basit bir demo hazırlamak (isteğe bağlı, zaman elverirse). Benden beklenen çıktı: 1. Kısa sürede uygulanabilir bağlantı şeması (KiCad, Fritzing veya PDF). 2. Çalışır örnek kaynak ko...